Here’s the deal: I wanted my Fashion Royalty, Poppy Parker & Nu Face heads to be more easily interchangeable and removable for when I want to change out a character’s “look”. Currently if I want to do that I either have to have multiple dolls (1 head, 1 body) for each character or else if I buy an “alternative look” head I have to go through the hassle of heating up the head, worrying about pulling it off, warming it up again, popping it on the new body (or the new head on the old body) and so on. I find that very stressful but I also don’t want to end up having 3 or 4 of each doll bodies just for a few different looks. Space is still at a premium in our house, you know?
This is a method that was suggested to me by my friend Will . I have done it with a few differences to use it on Integrity Toy’s Fashion Royalty, Poppy Parker and Nu Face lines. There is an unintended side effect with this mod — an increased range of motion at the neck allowing for more expressive head positions. 🙂
As usual, please be aware I am a risk-taker when it comes to my dolls and customizing them. I do it with the knowledge that in the process I may damage them. This modification is done at your own risk and I am only sharing my results and methods. If you plan on trying this I suggest using a doll you don’t mind so much if it ends up damaged.
What you’ll need:
To make 1 body & 1 head swap-able
- 1 body (I have done this on the Poppy Parker, FR3 and Nu Face 2.0 bodies)
- Neodymium Sphere Magnets. Minimum strength N35. I used 8mm ones but you can also use 5/16th sized ones too. (at the end of the post I’ll link to some places you can get them from) You’ll need 2 per head, 1 per body
- Lightweight cotton or muslin (about a 3 inch x 3 inch square)
- Vise Grip Pliers (small size)
- Safety Glasses
- Needle & thread
- Thin leather (pale in color to avoid any possibility of discoloring vinyl) or some other fabric that can provide friction to aid in holding head poses. You might have to experiment with what you have on hand. This is important though. As to thickness of the leather think of glove leather (fashion, not work gloves). About .50mm to 1mm in thickness.
- Hot water (close to boiling-I would not use boiling as it may make eyelashes come off?)
- Small bowl (for soaking the head and neck in)
- Patience. You’ll need some for this as it isn’t the fastest modification to complete. Don’t do it if you’re in a hurry!
- Here are a few of the supplies–sorry I forgot to snap a pic of everything.
Here we go! The fun, the excitement! The Nail-biting Drama!
First: get your supplies together and get your water on to boil. Get the small bowl ready so that you can put the near boiling water into it. Pour the water into the bowl.
I used near-boiling water and soaked Agnes’ head in it to soften the head up and get it off the body. If you’re comfortable using the heating pad, hairdryer or oven method to remove the head go ahead and do those instead. Get the water ready though since you will need it shortly.
After removing the head, empty the water and re-fill again with near boiling water. Then place the neck & neck knob area back in the bowl to soak for a couple of minutes. Don’t forget to put your safety glasses on!
After about 2 or 3 minutes you can remove it from the water. Be careful not to burn or scald yourself with the water (it’s going to drip out of the body).
Get your vise grips ready. It is important to grip and pull the knob out squarely (in a direct/ straight line). Not at an angle. Doing it at an angle will increase the chance of stress fracture and neck cracks considerably!! 🙁
Pull with firm, steady pressure. Keep it straight. Once the knob is removed get your magnet!
If you put the doll’s head in the water to remove it towel dry and allow to dry fully before going onto the next steps. (because you will be inserting fabric into the head you want to have it dry not damp or wet!) Also dry the body as best you can. Over night works ok, or if you’ve done it on an FR3 body you could remove the arms and lower torso to dry it off more thoroughly & quickly.
Next, get your fabric, magnets, needle and thread. Then insert the magnets into the center of the fabric and fold in half. Sew the base closed.
Wrap the thread around the magnets a couple of times. Tie off. Trim the fabric from the base of the fabric/magnet parcel.
Begin pushing it into the head.
The head holes vary in size so some will fit in better than others but they will all fit provided you are patient and apply appropriate pressure.
Now, get your leather and scissors and cut out two small circles (approximately a little smaller than a dime). You’ll trim them down more so the size is not exact.
Here is a photo to give you an idea of the leather’s thickness:
One will be for use inside the doll’s head-neck hole area, and the other will be for use over the neck-hole where the magnet sits.
Here is how to do it for the head part:
This is how both pieces should be positioned (I took the photo before trimming the neck’s piece)
At this point you’re almost done! YAY! All you’ve got to do now is gently position the head over the neck area (about 2 inches over it to avoid the magnetic pull) and then quickly put it in place (the magnets will help by attracting each other). It will probably take a couple of tries to get it on right (so that none of the leather circles show) but keep trying. You can always take them off and re position them when you need to.
And that’s it! You’re done! 😀
I did this to almost all of my FR/NF/PP dolls so I have been able to ditch most of the duplicate bodies and now can easily change heads around. The best thing about this is that inserting the magnets in this way allows me to remove them if I should want to re-root or partially re-root a head in the future. Also, I can now swap Giselle from the Poppy body to the high heeled Monogram body when I want her dressed up in heels! 😀 😀 😀
Here are a few photos of Agnes with her new magnet head/neck mod. She’s upside down to show that the magnets are strong enough to hold her head on even against gravity! 😀
Places to get Magnets From: Please note I don’t endorse these merchants I am only sharing where I got some of my magnets from and other places that carry them.
Thackery Handmade, LLC (on ebay) (this is where I got my magnets from. She ships quickly and the price per magnet is almost half that of K&J)
K&J MAGNETS Will got his magnets from here and they have a stronger pull strength. I used weaker magnets (N35) so your mileage may vary if you use these.